 |
|
Share
 InSinkErator Evolution Cover Control: Up to 40% offThe Evolution Cover Control� delivers all the great features that set the Evolution Series� apart, plus an extra margin of assurance. Activated by the magnetic CoverStart� Switch, it runs only when the cover is on. read more. |
INSINKERATOR 55 .55 HP DISP 220 VOLT 55 Product Detail
In-Sink-Erator International Disposal.55 HP Dura-Drive® heavy-duty induction motor.Stainless steel shredder ring for increased grinding efficiency.Stainless steel rotating shredder ring.Stamped stainless steel 360° swivel lugs.Engineered resin grind chamber won't corrode.Overload protection.Permanently lubricated bearings.Quick-Lock® mounting assembly for faster, easier installation.Plastic sink stopper resists corrosion.Standard stainless steel sink flange.Jam-Buster® wrench included to free jams.Standard Quiet Sound Reduction System.
Disposers also use the minimum amount of water and electricity necessary. On average, disposers use approximately one gallon of water per person per day, which amounts to one percent or less of a households total water consumption. Disposers use approximately 3 to 4 kilowatt hours of electricity; on average, that's less than 50 cents a year for operation.
How to Install a Evolution Disposer
Step 1: Install sink-mount assembly (new installation or different sink mounting)
Turn off the electrical supply at the circuit breaker or fuse box. Disconnect the sink drain and plumbing connections. Clean off the sink opening. Using plumber's putty, install the new disposer sink flange into the sink drain and connect the sink-mounting assembly. (Skip step two and move to step three.)
Step 2: Remove old disposer (replacements with similar sink mounting)
Turn off the electrical supply at the circuit breaker or fuse box. Disconnect the old disposer's plumbing connections and remove the disposer from its mounting. Disconnect the old disposer�s electrical connections.
Step 3: Make electrical connections
Connect the wiring to the new disposer following the code in your area.
Step 4: Dishwasher connections
If you are connecting the disposer to a dishwasher, be sure to knock out the dishwasher plug and remove the loose plug from the disposer. If you are not connecting the disposer to a dishwasher, then leave the plug intact.
Step 5: Connect new disposer
Mount the new disposer onto the sink-mount assembly and reconnect the plumbing--including the dishwasher hose if applicable. Turn on the electrical power to the disposer at the circuit breaker.
Step 6: Make plumbing adjustments
Lock the disposer in place, make final plumbing adjustments, and check for any leaks.
Recommended tools for installation: Slotted screwdriver, Adjustable pliers, Plumber's putty (if replacing sink flange), Electric hard-wire connector, 3/4-inch conduit connector, Power-cord kit (if needed).
Step 1: Install sink-mount assembly (new installation or different sink mounting)Turn off the electrical supply at the circuit breaker or fuse box. Disconnect the sink drain and plumbing connections. Clean off the sink opening. Using plumber's putty, install the new disposer sink flange into the sink drain and connect the sink-mounting assembly. (Skip step two and move to step three.)
Step 2: Remove old disposer (replacements with similar sink mounting)
Turn off the electrical supply at the circuit breaker or fuse box. Disconnect the old disposer's plumbing connections and remove the disposer from its mounting. Disconnect the old disposer�s electrical connections.
Step 3: Make electrical connections
Connect the wiring to the new disposer following the code in your area.
Step 4: Dishwasher connections
If you are connecting the disposer to a dishwasher, be sure to knock out the dishwasher plug and remove the loose plug from the disposer. If you are not connecting the disposer to a dishwasher, then leave the plug intact.
Step 5: Connect new disposer
Mount the new disposer onto the sink-mount assembly and reconnect the plumbing--including the dishwasher hose if applicable. Turn on the electrical power to the disposer at the circuit breaker.
Step 6: Make plumbing adjustments
Lock the disposer in place, make final plumbing adjustments, and check for any leaks.
Recommended tools for installation: Slotted screwdriver, Adjustable pliers, Plumber's putty (if replacing sink flange), Electric hard-wire connector, 3/4-inch conduit connector, Power-cord kit (if needed).
INSINKERATOR 55 .55 HP DISP 220 VOLT 55 Product Features
| |
|
Electrical Connections
Check to see if your disposer is hardwired or has a power cord plugged into an outlet. Depending on the electrical code in your area, you will have one type of connection or the other. Most disposers are sold without an attached power cord so that they may be used in either application. If you need a power cord, these can be purchased separately as an accessory. You may also purchase a unit with an attached power cord for this application.
Check to see if your disposer is hardwired or has a power cord plugged into an outlet. Depending on the electrical code in your area, you will have one type of connection or the other. Most disposers are sold without an attached power cord so that they may be used in either application. If you need a power cord, these can be purchased separately as an accessory. You may also purchase a unit with an attached power cord for this application.
Do It Yourself in 2012Save money this year by tackling home improvement projects yourself. Save up to 40% on the power tools, fixtures, and lighting you need for the job.
